The synthesis of polymer grafted nanoparticles that are stable at high salinities and high temperature with low retention in porous media is of paramount importance for subsurface applications including electromagnetic imaging, enhanced oil recovery and environmental remediation. Herein, we present an improved approach to synthesize and purify sub-100 nm IONPs grafted with a random copolymer poly(AMPS-co-AA) (poly(2-acrylamido-3-methylpropanesulfonate-co-acrylic acid)) by means of catalyzed amide bond formation at room temperature. The improved and uniform polymer grafting of magnetic nanoparticles led to colloidal stability of IONPs at high temperature (120 °C) in API for a month. The transport behavior of the polymer grafted IONPs was investigated in crushed and in consolidated Berea sandstone. The high poly (AMPS-co-AA) polymer level on the surface (∼34%) provided electrosteric stabilization between the NPs and weak interactions of the NPs with anionic silica and sandstone surfaces. This behavior was enabled by low affinity of Ca2+ towards the highly acidic AMPS monomers thus enabling strong solvation in API brine. In crushed Berea sandstone, the retention was reduced by three fold and nine fold relative to our earlier studies, given the improvements in the grafted polymer layer. For intact core flood experiments in Berea sandstone carried out at elevated temperature (65 °C) and pressure (1000 psi net confining stress), the retention was 519 μg/g, comparable to the value for crushed Berea sandstone. Furthermore, the addition of a relatively small amount (0.1% v/v) of commercially available sacrificial polymer (e.g., HEC-10) further reduced IONP retention to 252 μg/g or 0.17 mg/m2 by blocking retentive sites
Ultralow water content carbon dioxide-in-water (C/W) foams with gas phase volume fractions (ϕ) above 0.95 (that is <0.05 water) tend to be inherently unstable given that the large capillary pressures that cause the lamellar films to thin. Herein, we demonstrate that these C/W foams may be stabilized with viscoelastic aqueous phases formed with a single zwitterionic surfactant at a concentration of only 1% (w/v) in DI water and over a wide range of salinity. Moreover, they are stable with a foam quality ϕ up to 0.98 even for temperatures up to 120 °C. The properties of aqueous viscoelastic solutions and foams containing these solutions are examined for a series of zwitterionic amidopropylcarbobetaines, R-ONHC3H6N(CH3)2CH2CO2, where R is varied from C12–14 (coco) to C18 (oleyl) to C22 (erucyl). For the surfactants with long C18 and C22 tails, the relaxation times from complex rheology indicate the presence of viscoelastic wormlike micelles over a wide range in salinity and pH, given the high surfactant packing fraction. The apparent viscosities of these ultralow water content foams reached more than 120 cP with stabilities more than 30-fold over those for foams formed with the non-viscoelastic C12–14 surfactant. At 90 °C, the foam morphology was composed of ∼35 μm diameter bubbles with a polyhedral texture. The apparent foam viscosity typically increased with ϕ and then dropped at ϕ values higher than 0.95–0.98. The Ostwald ripening rate was slower for foams with viscoelastic versus non-viscoelastic lamellae as shown by optical microscopy, as a consequence of slower lamellar drainage rates. The ability to achieve high stabilities for ultralow water content C/W foams over a wide temperature range is of interest in various technologies including polymer and materials science, CO2 enhanced oil recovery, CO2 sequestration (by greater control of the CO2flow patterns), and possibly even hydraulic fracturing with minimal use of water to reduce the requirements for wastewater disposal.
To explain the effects of cationic amino acids and other co-solutes on the viscosity, stability and protein-protein interactions (PPI) of highly concentrated (≥200 mg/ml) monoclonal antibody (mAb) solutions to advance subcutaneous injection.
The viscosities of ≥200 mg/ml mAb1 solutions with various co-solutes and pH were measured by capillary rheometry in some cases up to 70,000 s−1. The viscosities are analyzed in terms of dilute PPI characterized by diffusion interaction parameters (kD) from dynamic light scattering (DLS). MAb stability was measured by turbidity and size exclusion chromatography (SEC) after 4 weeks of 40°C storage.
Viscosity reductions were achieved by reducing the pH, or adding histidine, arginine, imidazole or camphorsulfonic acid, each of which contains a hydrophobic moiety. The addition of inorganic electrolytes or neutral osmolytes only weakly affected viscosity. Systems with reduced viscosities also tended to be Newtonian, while more viscous systems were shear thinning.
Viscosity reduction down to 20 cP at 220 mg/ml mAb1 was achieved with co-solutes that are both charged and contain a hydrophobic interaction domain for sufficient binding to the protein surface. These reductions are related to the DLS diffusion interaction parameter, kD, only after normalization to remove the effect of charge screening. Shear rate profiles demonstrate that select co-solutes reduce protein network formation.